Submersible aerator centrifugal QXB7.5-100 with intake pipe and muffler
Installation diagram of submersible aerator
When the submersible aerator is in operation, the water pump impeller driven by the high-speed rotation of the submersible motor and the mud mixture are pushed and sprayed to form a negative pressure zone. The generated jet is sucked into the negative pressure zone of the nozzle through the suction pipe, and the gas is fully mixed with water and sludge in the jet pipe. The jet momentum of the jet diffusion pipe gradually converts into pressure energy and enters the diffusion.
In the diffuser, the mixed gas of gas, water, and mud is forced to undergo further shearing, crushing, and emulsification, ensuring the most sufficient oxygen dissolution in the water. At the same time, under the pressure of the fluid, oxygen carrying molecules and tiny bubbles are obliquely sprayed downwards from the diffusion tube nozzle, diffusing to form water and affect the sludge at the bottom of the biochemical tank. After stirring, they slowly rise from the bottom of the tank to the water surface, and the microbubbles stop leaving the water for a long time30 seconds is the complete dissolution and absorption of oxygen, improving oxygen transmission efficiency and oxygen.
The performance of centrifugal fans is influenced by the mud in the air, the high negative pressure and strong turbulence generated in the air, mixing, shearing, and the liquid and gas films that promote high-frequency oscillation. The diameter of bubbles is greatly reduced, the number of bubbles increases, and the specific surface area of bubbles increases. At the same time, the thinning of gas-liquid film can greatly reduce mass transfer resistance and facilitate the transfer of molecular oxygen from the gas phase to the liquid phase.
During the high-speed process, the jet has a high angular velocity due to the dispersing effect of high-speed rotation. The jet has strong penetration power, and the tiny bubbles travel far on the water, enhancing stirring, clogging, and aerobic capacity.
Centrifugal aerator aerationQi is a technology that makes air and water strong, with the purpose of dissolving oxygen dissolved in water or not requiring the introduction of gases and volatile substances into the air. In other words, it is a way to promote the exchange of gas and liquid substances.
It also has other important functions, such as mixing and blending. The mass transfer operation and dispersion mass transfer principle in which oxygen in air is converted into water and oxygen from the gas phase to the liquid phase through aeration are commonly proposed by the Lewis and Whitman double membrane theory.
The double membrane theory holds that there are gas and liquid film, air and liquid film and liquid film at the gas water interface, which belong to turbulent flowThe relationship between gas and liquid film belongs to laminar flow conditions, without convection. Under certain conditions, pressure and concentration gradients can occur. If the oxygen concentration in the liquid film is lower than that in water, the oxygen in the air will continue to disperse into the water through the liquid film. Obviously, the most effective method to overcome the membrane barrier of liquids is to change the "gas-liquid" interface.
Aeration agitation is like this. The detailed methods are: reduce the size of bubbles, increase the amount of foam, improve the level of liquid turbulence, improve the depth of aeration equipment, and extend the contact time of bubbles and liquid. Aeration equipment is a commonly used treatment method in sewage treatment.
Jiangsu Du'an Environmental Protection QXB7.5-100 Submersible Centrifugal Aeration Machine Installation Drawing Products are widely availableAnd the cities of Beijing, Tianjin, Shanghai, Chongqing, and Hechuan in China yongchuan Jiangjin City Nanchuan city
Shijiazhuang City, Hebei Province--Xinji City, Gaocheng City, Jinzhou City, Xinle City, Luquan City, Zhangjiakou City
Chengde City, Qinhuangdao City, Tangshan City--Qian'an City, Zunhua City, Langfang City - Sanhe City, Bazhou City
baoding--Dingzhou City, Zhuozhou City, Anguo City, Gaobeidian City, Hengshui City - Jizhou City, Shenzhou City
Cangzhou City--Botou City, Renqiu City, Huanghua City, Hejian City, Xingtai City - Nangong City, Shahe City
handan city--Wu'an City, Shanxi Province, Taiyuan City - Gujiao City, Shuozhou City, Datong City, Yangquan City, Changzhi City - Lucheng City
Jincheng--Gaoping City Xinzhou City Yuanping City Jinzhong City Jiexiu City Linfen City Houma City Huozhou City
Lvliang--Xiaoyi City, Fenyang City, Yuncheng City, Yongji City, Hejin City, Inner Mongolia Autonomous Region, Hohhot City
Baotou City, Wuhai City, Chifeng City, Tongliao City--Hulunbuir City Hulunbuir City Manzhouli City Zhalantun City Yakeshi City Genhe City Erguna City
Ulanqab City, Ordos City--Bayannur City, Fengzhen City (Xing'an League) - Alshan City, Ulanhot City(
(Xilingol League)--Xilinhot City, Erenhot City, Liaoning Province, Shenyang City, Xinmin City, Chaoyang City, Beipiao City, Lingyuan City, Fuxin City
Tieling--Tiaobingshan City Kaiyuan City Fushun City Benxi City Liaoyang City Dengta City Anshan City Haicheng City
Dandong City--Fengcheng City, Donggang City, Dalian City - Wafangdian City, Pulandian City, Zhuanghe City, Yingkou City - Dashiqiao City, Gaizhou City
Panjin City Jinzhou City--Linghai City, Beining City, Huludao City, Xingcheng City, Changchun City, Jilin Province, Dehui City, Jiutai City, Yushu City
Baicheng--Da'an City Taonan City Songyuan City Jilin City Panshi City Jiaohe City Huadian City Shulan City
Siping City--Shuangliao City, Gongzhuling City, Liaoyuan City, Tonghua City, Meihekou City, Ji'an City, Baishan City, Linjiang City
(Yanbian Korean Autonomous Prefecture)--Yanji City Tumen City Dunhua City Hunchun City Longjing City and Longshi City
Harbin City, Heilongjiang Province--Shuangcheng City Shangzhi City Wuchang City Acheng City Qitaihe City Qiqihar City Nehe City
Heihe--Beian City Wudalianchi City Daqing City Hegang City Yichun City Tieli City Jiamusi City Tongjiang City Fujin City
Jixi City, Shuangyashan City--Hulin City Mishan City Mudanjiang City Muling City Suifenhe City Hailin City Ning'an City
suihua--Zhaodong City, Hailun City, Jiangsu Province, Nanjing City, Xuzhou City, Pizhou City, Xinyi City
Lianyungang City, Suqian City, Huai'an City, Yancheng City--Dongtai City, Dafeng City, Yangzhou City, Yizheng City, Jiangdu City, Gaoyou City
Taizhou--Jingjiang City, Taixing City, Jiangyan City, Xinghua City, Nantong City, Haimen City, Qidong City, Tongzhou City, Rugao City
Zhenjiang--Yangzhong City Danyang City Jurong City Changzhou City Jintan City Liyang City Wuxi City Jiangyin City Yixing City
suzhou--Wujiang City Kunshan City Taicang City Changshu City Zhangjiagang City Zhejiang Province Hangzhou City Lin'an City Fuyang City Jiande City
Huzhou City Jiaxing City--Pinghu City, Haining City, Tongxiang City, Zhoushan City, Ningbo City, Cixi City, Yuyao City, Fenghua City
Shaoxing--Zhuji City Shangyu City Shengzhou City Quzhou City Jiangshan City Jinhua City Lanxi City Yongkang City Yiwu City Dongyang City
Taizhou--Linhai City, Wenling City, Wenzhou City - Rui'an City, Leqing City, Lishui City - Longquan City, Hefei City, Anhui Province
Fault phenomenon
Reason
Clearing method
Power equipment overload
1. The inlet water tank does not meet the requirements
The blades of the submersible aerator are surrounded by debris
Friction occurs between the blades and guide vanes of a submersible aerator
The speed of the submersible aerator exceeds the specified value
1. Improve water inlet conditions
2. Remove debris and clean with water
3. Check the wear of the blades and readjust the installation
Adjust the prime mover to meet the rated speed
Decreased aeration or no aeration
The diving depth of the water aerator is too deep
Wear of the outer circle of the impeller blades or partial damage of the blades
The direction of diving aeration is wrong
The impeller is loose
5 submersible aerators are clogged with impurities
1. Improve the submersible aerator
2. Replace the impeller
3. Correct the rotation direction
4 fastening screws
5. Remove debris and use water to clean up
There is noise or vibration during operation
The foundation of the submersible aerator is not firm enough or the nuts are loose
Friction occurs between the impeller and guide vanes
3. Loose impeller screws or damaged blade parts
4. Unstable water inflow state
5 submersible aerators are clogged with impurities
1. Strengthen the foundation and tighten the screws
2. Check the clearance between the impeller and guide vanes
3. Tighten the screws or replace the impeller
4. Adjust the water inlet status
5. Remove debris and clean with water
The submersible aerator cannot be started or the fuse is blown
1. Winding, connector or cable open circuit
2. The submersible aerator is blocked
3. Leakage or water leakage
4 Short circuit
1. Check with an ohmmeter
Cut off the power and remove debris
3. Check the insulation, if it is below the specified value, it must be dried
4. Use after inspection and maintenance
After starting the submersible aerator, the circuit breaker and overload device are disconnected
1. Low voltage
2. High voltage
3. Incorrect motor wiring or confused connectors
4 Control cabinet electrical malfunction
1. If not in use temporarily or if the voltage drops due to a long circuit, the power cord should be thickened
Install two transformers and adjust the voltage to the specified value
3. Adjust wiring and connectors
4. Check and replace electrical components