Redwood furniture wood dryer

The wood dryer is suitable for drying precious wood (rosewood, rosewood, sourwood, chicken wing wood, etc.), anti-corrosion wood, and miscellaneous wood (cedar, pine, etc.).

　　Introduction to Wood Drying Machine Products:

Fresh wood contains a large amount of moisture, which will continuously evaporate in specific environments. The natural evaporation of water can cause defects such as shrinkage, cracking, bending deformation, and mold growth in wood, seriously affecting the quality of wood products, especially for some expensive and precious woods such as rosewood, nanmu, huanghuali wood, rosewood, imported wood, furniture boards, etc. Therefore, wood must undergo forced (controlled) drying treatment before being made into various types of wood products. Proper drying treatment can overcome the above-mentioned wood defects, improve the mechanical strength of wood, and enhance the processing performance of wood. It is an important technical measure for rational utilization of wood and increasing its value, and it is also an essential primary process in the production of wood products. So, the wood dryer is a necessary processing equipment for wood processing plants and home processing plants. The wood drying room is safe, environmentally friendly, pollution-free, and has no exhaust emissions. The operating electricity cost is ultra-low, and there is no need for personnel to be on duty during fully automatic operation. It is a replacement product for traditional wood drying equipment. It effectively solves various problems of traditional dryers, such as pollution, cost, and so on. In terms of drying appearance, 'blue sky'Wood dryerThe effect is also significantly higher than other drying methods.

　　Principle of Wood Drying Room:

The wood drying room consumes a small amount of electricity, works with a compressor, and absorbs and releases heat through a working medium (also known as refrigerant) to achieve heating. The wood drying room mainly consists of heating main unit, heat exchanger, circulating fan, insulation drying room, dehumidification fan, etc. The heat exchanger and circulating fan are placed in the insulation drying room. The high-temperature and high-pressure gas generated by the heating host passes through the heat exchanger, and the circulating fan sends the heat generated by the heat exchanger into the drying room to heat and dry the materials inside. The water vapor generated by the materials is then discharged to the outside of the drying room by the dehumidification fan at the top of the drying room to achieve the purpose of drying.

　　What are the drawbacks of traditional drying methods in production:
The current situation is that we rely on the weather to make a living. Currently, the traditional method of drying items is mainly through sun drying, which uses some mechanical assistance to dry them. However, the items are also dried for a certain distance before being placed in the oven. Therefore, production is greatly affected by weather conditions.

Current situation 2: The traditional drying method requires a large amount of labor, but due to weather conditions, it requires continuous drying, folding, and re drying, which incurs significant labor costs. Even with traditional ovens, multiple repositioning adjustments are required due to uneven baking temperatures.

Current situation three: Lack of hygiene guarantee

Traditional drying, due to the use of open air drying, is greatly affected by surrounding mosquitoes and dust during the drying process. Especially for food products, the quality cannot meet the requirements of food grade, which is also a reason that restricts many enterprises from expanding and entering the market.

Current situation four: Even if drying equipment is used, it is found that the energy consumption is very high. Some companies have recognized the three major problems mentioned above, so they have introduced some drying equipment to assist in drying. However, in practical applications, it has been found that there are high energy consumption and uneven drying. Moreover, traditional drying equipment cannot directly put fruits with water into the oven, so overall, it is still unable to escape the process of sun exposure.

　　Characteristics of the "Blue Sky" Wood Drying Machine Equipment:
1. The drying temperature is accurate and controllable. The wood dryer equipment uses a dry wet bulb to accurately control the temperature and humidity inside the drying room.

2. Low operating costs. Adopting a touch screen intelligent control system, the system can set multiple drying time periods, and each time period can set different operating modes (cooling/heating), temperature, humidity, operating time, dehumidification time, etc., without the need for personnel supervision.

3. Dried wood is less prone to cracking and deformation.

　　Redwood dryer

　　Redwood dryer product introduction:

　　Redwood dryerThis is a product designed by Gongyi Blue Sky Machinery Factory specifically for rosewood furniture. It is a professional dryer used to dry various types of wood such as large leaf rosewood, small leaf rosewood, old rosewood, and yellow pear. It uses air as a heat source, which is not only easy to operate, but also can control temperature and humidity, ensuring the quality of the wood.

　　Precautions for Redwood Drying Machine:

Redwood belongs to the category of difficult to dry broad-leaved wood. Redwood contains a lot of content and has a high density. The water transfer channels in the wood are not very smooth. During the drying process, if the temperature is too high, it is easy for the surface to harden, and the water on the inner surface cannot evaporate, causing external cracking. If the temperature inside and outside is unbalanced, it is also very easy to cause internal cracking of the wood, which can have an economic impact.

　　Advantages of Redwood Drying Room:
The redwood drying room adopts hot air circulation heating to evenly heat the wood. In terms of control, the redwood drying room has ten temperature ranges that can be adjusted. Different temperature controls are used at different stages of wood moisture content to evenly remove moisture during the drying process, avoiding surface hardening and cracking.

　　Working principle of redwood drying oven:

The redwood drying box mainly consists of four parts: a finned evaporator, a compressor, a finned condenser, and an expansion valve. By continuously evaporating the working fluid (absorbing heat from the outdoor environment), compressing, condensing (releasing heat in the indoor drying room), throttling, and then evaporating again, the heat from the external low-temperature environment is transferred to the drying box. The refrigerant circulates in the system under the action of the compressor. It completes the process of gas pressure rise and temperature rise (up to 100 ℃) inside the compressor. It enters the internal unit and releases high-temperature heat to heat the air inside the drying box. At the same time, it is cooled and converted into a liquid state. When it runs to the external unit, the liquid state quickly absorbs heat and evaporates, and then transforms into a gas state again. At the same time, the temperature can drop to -20 ℃~-30 ℃. At this time, the air around the heat absorber will continuously transfer heat to the refrigerant.

　　Precautions for drying rosewood:

Redwood belongs to the category of difficult to dry broad-leaved wood. Redwood contains a lot of content and has a high density. The water transfer channels in the wood are not very smooth. During the drying process, if the temperature is too high, it is easy for the surface to harden, and the water on the inner surface cannot evaporate, causing external cracking. If the temperature inside and outside is unbalanced, it is also very easy to cause internal cracking of the wood, which can have an economic impact.

　　Furniture dryer

Traditional furniture paint drying generally uses electric heating, sun lamps, hot air stoves, natural air drying, etc. Among them, electric heating, solar lamps, and hot air stoves consume too much energy, resulting in uneven heating during the drying process, difficult temperature control, and difficult quality assurance. Natural drying is greatly affected by weather conditions. Different climates not only affect the drying time of furniture and paint, but also seriously affect the quality. For example, in humid seasons, it can take several days to dry, and in summer when the temperature is too high, there may be problems such as bubbles on the paint surface. The air dryer has functions such as raising, lowering, and dehumidifying, and can be adjusted according to the characteristics of the paint to maintain a suitable temperature, ensuring that products are not affected by weather throughout the year and greatly improving quality.

　　Furniture dryer product introduction:

Produced by Blue Sky Machinery Factory in Gongyi CityFurniture dryerIt is a device that can obtain low-grade heat energy from air, water, or soil in nature, and provide high-grade heat pumps that can be used by people through compressor work.

　　Furniture paint drying process:

The dehumidification system can automatically control the dehumidification according to the humidity of the drying room (for example, the humidity controller is set to 50%; the dehumidification time is set to 15 minutes, and the dehumidification fan is turned on for 1 minute for dehumidification. Every 15 minutes, when the humidity exceeds 50%, the dehumidification fan is turned on for dehumidification; if the humidity in the drying room is below 50% after 15 minutes, the dehumidification fan is still turned off and does not dehumidification. After a period of time, when the humidity reaches 50%, the dehumidification fan is turned on for 1 minute for dehumidification and then turned off. After turning off, the timer is restarted for 15 minutes, and dehumidification is turned on again when the humidity exceeds 50%. This cycle repeats until the humidity reaches 50%. Drying requirements).