1. Fluid used: Compressed air

2. Operating pressure: 5kg/cm ² (70psi)

3. High usage pressure: 7kg/cm ² (95pis)

4. Surrounding temperature: -10 ° C~+70 ° C (but can only be used in an unfrozen state).

5. Lubricating oil: The air pressure supply line delivers oil It is recommended to use JIS K2213 (or add machine 6. Oil ISOVG32) similar products.

7. Continuous use: Yes (but continuous operation without load is not allowed).

8. It is recommended to use a rotation speed of (0.3~1) x when the output is high.

Attention must be paid when using:

A、 Improper connection of the output axis driven by the pneumatic motor can lead to poor operation and cause malfunctions.

B、 The axial and radial loads on the axis of the motor must be below 1KG.

C、 When a malfunction is detected, it should be stopped from continued use and checked and adjusted by professional maintenance personnel.

D、 After installation, do not use it directly. Observe it by idling with your hands. If there is no abnormal noise or friction, it can be used normally.

E、 Do not arbitrarily remove the parts of the pneumatic motor before use, as it will not only damage the tool but also affect the safety of the operator.

F、 During use, handle with care, do not work with illness, and do not throw, toss, drop, smash or use unreasonably.

G、 Check whether the pneumatic motor itself and pneumatic accessories are reliably connected to prevent damage or injury during high-speed operation.

Attention must be paid to:

A、 The main cause of malfunctions in air pressure machines, including pneumatic motors, is mostly due to the entry of foreign objects such as dust.

Before piping, compressed air must be used to clean the air inside the pipe, and care must be taken not to allow cutting powder or sealing tape to enter

Fragments, dust or rust enter the piping.

B、 Air pressure machines (air filters, air pressure regulators, fuel injectors, directional switching valves, etc.) should be installed as much as possible

Placed near the pneumatic motor.

C、 If air pressure is directly supplied, sometimes there may be some pressure fluctuations, so stable horsepower, torque, or revolutions cannot be obtained

Therefore, an air pressure regulator must be used.

During operation, attention must be paid to:

A、 Confirm if the rotation direction is correct or if there is any abnormal installation between the driven object and the axis.

B、 The control and stability of the speed of the pneumatic motor must be adjusted from the perspective of air supply, so the exhaust side can avoid generating back pressure.

C、 Do not allow the motor to rotate continuously or at high speed without load. If it continues to idle without load, the rotational speed will increase excessively and the pneumatic motor will be damaged.

D、 When conducting a load test run, use an air conditioning valve to gradually increase the number of rotations to the required number. reach

When the horsepower is high, if it exceeds this rotation number again, the pneumatic motor may be damaged. Pay attention to the correct use of pressure.

E、 Regularly check the pneumatic motor (approximately every three months). Maintain the pneumatic motor.

Operating instructions:

a. Please close the air valve before opening the air compressor.

B. Adjust to work pressure, but do not exceed 100psi (7 bar).

7、 Installation precautions:

a) The air inlet pipeline must be equipped with an automatic oil feeder, which can extend the service life and increase power by using automatic lubrication with clean oil.

b) The pipelines and control valves are of sufficient size to ensure appropriate air flow.

Main products of the company:Pneumatic diaphragm pump‖Electric diaphragm pump‖Micro Diaphragm Pump‖Magnetic pump‖Oil drum pump‖drum pump‖Metering pump‖self priming pump‖screw pump‖Concentrated slurry pump‖Corrosion resistant pump‖chemical pump‖Sewage pump‖Submersible pump‖centrifugal pump‖Pipeline pump‖oil pump‖vacuum pump‖sanitary pump‖Submersible pump‖Multi-stage pump‖Colloid mill‖rotor pump‖deep-well pump‖Vortex pump‖Booster pump‖Refueling pump‖Pump‖