Product Introduction:

SJCCFull automatic deodorizer spray can automatically deodorize hotels, shopping malls, office buildings, toilets and other spaces by injecting neutral deodorant, automatically disinfect indoor by injecting neutral disinfectant, and automatically humidify local air by injecting tap water. The machine is designed for wall hanging use and can also be placed upright for a short period of time,SJCCThe atomizing box of the spray is made of stainless steel liner, and the shape structure is made of cold rolled steel plate sprayed with plastic, which not only ensures the beautiful appearance but also meets the requirements of equipment anti-corrosion.SJCCSpray machine with5.5A self-contained water tank with a capacity of kilograms of water, with a water inlet connected to the upper end of the tank and a drain switch at the lower end.ZY-1800The ultrasonic spray adopts the digital time sequence controller for automatic cycle control. The automatic cycle control cycle is from one second to ninety-nine minutes and fifty-nine seconds. The working time and stop time can be set at will. After setting, it can work continuously without the need of personnel.SJCCThe output of the ultrasonic full-automatic deodorizer spray is a rotatable fan-shaped nozzle. The fan-shaped nozzle and bushing can also be removed according to actual needs, and the self providedΦ75PVCPipeline, with a transmission distance of not less than5Rice.SJCCThe full-automatic deodorizer spray is equipped with six vibrator integrated atomization components and a water free protection device, and the diameter of generated fog particles is only less than10μmThe particles are uniform and can remain suspended in the air for a long time. Full automatic deodorizer spray has no mechanical drive, no noise interference, no pollution, high atomization efficiency, low failure rate, low energy consumption, and is an efficient, reliable, and practical spray deodorizer.

Equipment installation (as shown in the diagram)1）

openSJCCFor the packaging of full-automatic deodorizer spray machine, take out the equipment, remove the wall mounting plate behind the equipment, select the equipment installation position, fix the equipment mounting plate horizontally at the installation position, hang the upper end of the spray machine on the upper end of the installation plate, and fix the lower end of the spray machine on the installation plate with two screws, so far, the fixed installation is complete. Next, connect the power cord to the power outlet and open the water supply port③ Add water solution to the water tank5About kilograms, then turn on the power switch and set the timing controller (see setting method)2）， Press the start button to start timing the machine.

Controller settings (as shown in the figure)2）

　　 SJCCThe setting and limiting range of the controller of the full-automatic deodorizer spray: the working time and interval time are99minute59Countdown in seconds. After connecting the power, the controller displays two rows of four digit red fluorescent numbers and a red indicator light⑴Shining, this is the interval state, and the output is0, upper row number⑶Gradually decreasing, decreasing to0Green output indicator light⑵Illuminated, this is the working state, also the same as the upper row of numbers⑶Reduce to0When the green output indicator light goes out, it enters the interval state again, and the output is0Complete a conversion cycle. When necessary, the interval time and working time can be adjusted according to the following steps:

Press the adjustment key (6) once, and the number in the top row (3) is the first1Flashing position, press the number adjustment key (7) to set the interval time to ten minutes; Afterwards, press the adjustment key (6) once, and the number in the top row (3) will be the first2Flashing position, press the number adjustment key (7) to set the number of minutes for the interval, and then set the value of seconds for the interval; Press the adjustment key (6) again, and the number (4) in the bottom row will be displayed1Flashing position, press the number adjustment key (7) to set the working time to ten digits in minutes; Afterwards, press the adjustment key (6) once, and the number (4) in the bottom row will be displayed2Flashing position, press the number adjustment key (7) to set the number of working hours in minutes; Based on this, set the working time second value; After the setting is completed, wait quietly for the last flashing stop, and then follow the diagram2 Press the start button (8) once, the red indicator light (1) flashes, entering the interval state and starting the cyclic operation of the set value. After completing this task and shutting down, the controller will automatically memorize the set values, and will automatically enter the memorized setting cycle working state after the next power on.

Performance indicators: