Supports 250M 8CH mode

1. The sampling rate can be set to 100M, 50M, 20M, 10M, 5M... up to 100Hz. The corresponding sampling resolutions are 10ns, 20ns, 50ns, 100ns... 10ms(In 8-channel mode, the sampling rate can reach 200M)

2,16 channels of digital signal input, with an input voltage range from -1V to 6V. A voltage higher than 1.6V is considered high, and the threshold is precise. There is a comprehensive input signal protection mechanism internally.

3. Adopting mature and complete USB2.0 high-speed interface chips, it is backward compatible with USB2.0 full speed and USB1.1, with fast data transmission, stable data transmission, and good compatibility.

4. The USB interface supports automatic connection, which means that when the software interface is enabled, it can automatically recognize whether the hardware is connected, without the need to connect the hardware before opening the software like most traditional USB devices.

4. Support protocol analysis, currently supported protocols include SPI, UART, I2C, PWM, and will be continuously added in the future. The content parsed from the protocol is displayed in a list format, which is more intuitive and easy to analyze. Clicking on the parsed content automatically locates the cursor at the corresponding waveform position, which is an important advantage of this logic analyzer software.

5. Adopting variable data acquisition and a compression mode with variable time bits, the maximum compression ratio is (2 to the 47th power): 1. Using two IS61LV25616 storage chips with a total capacity of 8Mbits, it can collect 128K to 256K variables regardless of the acquisition time! Please compare the acquisition time with any logic analyzer in the world that supports variable acquisition!

6. Adopting high-speed asynchronous static memory with a bit width of 32 bits, a capacity of 1MBYTE, and a storage bandwidth of 400MBYTES/SECOND

7. You can save and open workspace settings and collected data. For future analysis.

8. Both the driver and the upper computer fully support WIN2000, XP, VISTA, WIN7 32-bit, and WIN7 64 bit operating systems, and have been tested and approved.

9. Simplified Chinese and English operating interfaces.

10. Software? Do you have a lying down system with a clear outline? The I and O keys are used to zoom in and out of the waveform, respectively. The 1 and 2 keys are used to view the area centered around cursor 1 and 2.

11. The hardware adopts FPGA and uses upper computer software for FPGA dynamic configuration, which can be flexibly upgraded without any modification to the hardware.

12. It fully supports various triggers, including high and low edge triggers, high and low level triggers, as well as combinations of these four triggers, and supports automatic data collection.

13. The input impedance is 100K ohms and the capacitance is 5PF. The mainstream parameters prevent impedance loads from occurring.

There are two acquisition modes, one is the recommended variable storage acquisition, and the other is the traditional 100M sampling rate continuous storage acquisition.

15. We will continuously update the existing software functions and develop new tool software based on LWLA1016, which will be provided for free.

16. We have implemented a multi-channel frequency meter and developed a dedicated software interface to connect with LWLA1016. At the same time, we can collect 16 channels of data and display them in real-time. Due to the use of asynchronous counters, the measured signal is treated as a constant signal to control the measurement period of the accumulation register. The upper limit of the frequency meter is 250M (measured). The interface is concise and clear, as shown in the following figure: (Green represents MHZ, yellow represents KHZ, and white represents HZ)

Real time frequency meter, up to 150M, with a refresh rate of one second

Support high level, low level, rising edge, falling edge, and combination trigger settings

Real time channel display, real-time display of data collected from the channel

Improved waveform production interface and tools

Support group settings, as well as base and color only settings

Each interface element can be personalized and customized

The shipping list is shown in the following figure:

1100M 16 channel logic analyzer host.

2. 20 clips.

3. A 20PIN connector with a length of about 30CM, equipped with a 20PIN plug and a 30CM long marking line, with CH1... CH16 and 4 GND markings on it.