KYB typeMobile self-priming skateboard pump】Product Introduction:

The advantage of KYB type (stainless steel, aluminum alloy) self-priming sliding plate pump is that it does not need to inject oil into the pump before operation, and can suction and transport oil by itself. At the same time, it is not afraid of oil stains and general debris, and is not afraid of air entering the pipeline. Therefore, when oil tanks, tank trucks, etc. need to suction and clean the bottom oil, using this pump will significantly improve work efficiency, reduce oil waste, and increase economic benefits. In addition to the above characteristics, it also has the following significant features:
1. Vacuum height, which is about 25% higher than similar products;
2. High utilization rate of shaft power, low input power, and high output flow rate;
3. Long service life, few vulnerable parts, and simple maintenance;
4. Compact structure and easy to use.
The KYB mobile self-priming skateboard pump can pump and transport various lubricating oils with a viscosity of less than 200 cS, including gasoline, kerosene, diesel, liquefied gas, and other lubricants. It is mainly used for pumping, pouring, loading, and sweeping in oil depots, stations, gas stations, and automobile fleets. The stainless steel series can also transport acids, alkalis, oxidants, and other corrosive media of any concentration.

KYB typeMobile self-priming skateboard pump】Model meaning:

KYB typeMobile self-priming skateboard pump】Usage and characteristics:

KYB type (stainless steel, aluminum alloy, cast iron)Self suction skateboard pumpIt is a latest product independently developed, researched, and produced by our company both domestically and internationally. This pump has unique advantages such as strong self-priming ability, high utilization of shaft power, and long service life. In harsh environments such as mountains and rivers without power supply, it can be equipped with a diesel engine as a power device. It is an ideal mobile fire pump in specific environments, making it widely applicable. Its advantage is that there is no need to inject oil into the pump before work. It can suction and transport oil by itself, while not afraid of oil stains and general debris, and not afraid of air entering the pipe. Therefore, when oil tanks, tank trucks, etc. need to suction and clean the bottom oil, using this pump will significantly improve work efficiency, reduce oil waste, and increase economic efficiency. In addition to the above characteristics, it also has the following significant features:
1: Vacuum height, its vacuum degree is about 25% higher than similar products;
3: Long service life, few vulnerable parts, and easy maintenance;
4: The structure is compact and easy to use and maintain.
2: High utilization rate of shaft power, low input power, and high output flow rate;
6: Connect the elastic coupling directly to the drive motor or diesel engine and install it on the common chassis.
5: The pump is equipped with a safety valve. When the pump or pipeline malfunctions or the discharge safety valve is accidentally completely closed, resulting in high pressure and high pressure impact, the safety valve will automatically open to discharge some or all of the high-pressure liquid back to the low-pressure chamber, thereby protecting the pump and pipeline.
7: KYB typeSelf suction skateboard pumpFlexible graphite with good elasticity, high and low temperature resistance, stable chemical properties, and moisturizing effect can be used as fillers for sealing. This product can be used for suction and transportation of light oil, chemical, kerosene, and various lubricating oils with a kinematic viscosity of less than 200 cS. It is equipped with copper gears to transport low point liquids such as gasoline, benzene, etc. It is mainly used for suction, pouring, loading, and cleaning of oil depots, gas stations, train stations, automobile fleets, oil tankers, etc. It can also be used as a pump for mobile refueling trucks, oil tankers, etc. The stainless steel skateboard pump series can also transport beverages as well as any concentration of acids, alkalis, oxidants, and other corrosive media. The cast iron skateboard pump series can also transport water quality materials as mobile fire pumps.

KYB typeMobile self-priming skateboard pump】Installation dimension diagram:

KYB typeMobile self-priming skateboard pump】List of vulnerable parts:

KYB typeMobile self-priming skateboard pump】Usage and precautions:

1. The workplace should strictly comply with specific standards and requirements for explosion-proof environments.
2. The pump should not idle freely when not in operation, and it is best not to idle for more than two minutes during operation.
3. The electrical circuit system should be operated according to oil tank operation, protection, safety knowledge and procedures, and reliably grounded.
4. Whether the rotation direction of the pump meets the requirements. (If viewed from the pump to the motor, the rotation direction is counterclockwise)
5. When starting with power on, if the motor cannot rotate normally, the power should be immediately turned off to investigate the cause and prevent the motor from burning out.
6. Before the end of work, the oil suction can be lifted off the oil surface, the remaining oil in the tube can be drained, and the power can be turned off immediately.
7. When storing the pump, it is best to store it in a professional room. When using it, do not let it get wet with rainwater or other liquids, and try to avoid the small wheels from being contaminated with oil or grease.
8. Connect the power supply, instantly start the motor, and check from the motor hood whether the direction of rotation is consistent with the arrow direction indicated on the front cover of the pump body. Otherwise, adjust the power connector.
9. After the preparation work of the electrical circuit and oil pipeline is completed, the work can be started. After about one minute of starting, the oil should be sucked and transported normally. Otherwise, inspection, analysis, and troubleshooting should be carried out.
10. The power cord should use high-quality rubber sheathed cables with specifications of 3 * 1.5+1 * 1 or slightly larger capacity. The power supply is 380V, and the power switch should use an air switch of 15A or above. At the same time, try to shorten the length of the cable and the distance between the switch and the pump working point.
11. The oil pipeline adopts steel wire braided rubber hose with the same specifications as the skateboard pump (nylon hose or oil resistant rubber hose can be used for the discharge pipe), which is connected to the KCB standard hose female end joint and sealed with pipe clamps, and then connected to the inlet and outlet of the pump body respectively. The length of the suction pipe should not exceed 8 meters, and the length of the discharge pipe should not exceed 40 meters.
12. This series of pumps has good self-priming performance, and no liquid needs to be injected before each pump start. There is also no need to add lubricating fluid during daily operation.
13. The pump uses an elastic coupling to transmit power, which can compensate for small deviations caused during installation and provide good buffering when the pump is subjected to inevitable hydraulic impacts during operation.
14. After the work is completed, unscrew the oil drain valve located at the bottom of the pump casing, twist the motor from the motor connector, and drain the oil stored in the pump.
15. The cast iron sliding plate pump should be maintained when transporting water quality materials, with a maintenance cycle of fifteen days. Rust proof powder can be added to prevent the pump body from rusting and affecting normal operation.

KYB typeMobile self-priming skateboard pump】Structure diagram:

KYB typeMobile self-priming skateboard pump】Performance parameters:

Declaration:Due to continuous product updates, all text, data, and images in this article are for reference only. Please contact our marketing department for detailed information on the performance parameters, usage scenarios, material requirements, structure, installation dimensions, and price of the KYB mobile self-priming skateboard pump. We will do our best to provide you with high-quality service.