Henan Sitong Boiler Co., Ltd
Home>Products>Methanol fired condensing steam boiler
Methanol fired condensing steam boiler
Product Introduction: The condensing boiler utilizes efficient condensers and energy-saving devices to absorb the sensible heat and latent heat releas
Product details

Product Introduction

20181031011732593.jpg WNS low nitrogen condensing gas steam boiler adopts a fully wet back combustion chamber, which is connected to the rear tube plate flange. The boiler adopts full butt welding for more reliable quality. The combustion chamber of the boiler is composed of a large-diameter full corrugated furnace liner, with a large combustion space, complete fuel combustion, effective absorption of thermal expansion, and a large radiation heating surface. To improve thermal efficiency, an energy-saving device and a condenser are arranged in sequence at the outlet of the front smoke box of this type of boiler, which has a significant energy-saving effect.

This boiler has high and low water level alarm functions, low water level interlock protection functions, and overpressure interlock protection functions. In order to effectively monitor and control water level and pressure, this boiler is equipped with a water level gauge, an electrode type water level control alarm, a pressure gauge, and a pressure controller, which enable the boiler to have high and low water level alarm/low water level interlock protection, steam pressure overpressure interlock protection, automatic ignition of the boiler, automatic adjustment of burner firepower, and shutdown protection, ensuring the safe operation of the boiler.

The fuel of this product is sprayed out from the burner, ignited by high-pressure electronic ignition, and burned under slight positive pressure in the furnace chamber. The high-temperature flue gas after combustion enters the second return path by turning 180 ° from the rear smoke chamber, and then enters the energy-saving device and condenser through the front smoke box, and is discharged into the atmosphere through the chimney.

The front smoke box adopts an integral double door setting, with double-layer sealing of the smoke box door. This form has good integrity, beauty, and elegance, and is also easy to open during maintenance. The chimney height is configured to be 8 meters before leaving the factory. Users should determine the actual height according to the requirements of the environmental impact assessment report approved by the local environmental protection department, but not less than 8 meters.

Performance advantages

1. Adopting a wet back structure, offsetting the furnace and corrugated furnace liner, greatly improving the heating surface and strength
2. The boiler has a large heating surface area, fast temperature and pressure rise, and easy operation.
3. Reasonable and compact structure, strong load adaptability, complete combustion, high thermal efficiency of 105%
4. The condenser is made of high-quality sulfuric acid dew point corrosion resistant steel 09CrCuSb (ND steel) spiral finned tubes, which have a long service life.
5. The condenser is installed on the upper part of the boiler, without occupying any space, and the condensed water on the heat transfer surface can also be naturally discharged.
6. The safety accessories of the main body are complete, ensuring safe and economical operation.
7. Equipped with high-quality and high-performance burners, the combustion is stable and reliable.
8. High degree of automation, saving labor.
9. The boiler has a small volume, light weight, small footprint, and low infrastructure investment.

technical parameter


model WNS1-1.25-Q WNS2-1.25-Q WNS4-1.25-Q WNS6-1.25-Q
Rated evaporation capacity 1t/h 2t/h 4t/h 6t/h
Rated steam pressure 1.25MPa 1.25MPa 1.25MPa 1.25MPa
Rated steam temperature 194℃ 194℃ 194℃ 194℃
Water supply temperature 20℃ 20℃ 20℃ 20℃
Energy saving device inlet/outlet temperature 40℃/90℃ 42℃/78℃ 40℃/90℃ 40℃/76℃
Inlet/outlet temperature of condenser 20℃/40℃ 20℃/42℃ 20℃/40℃ 20℃/40℃
Pollution discharge rate 3% 3% 3% 3%
Cold air temperature 20℃ 20℃ 20℃ 20℃
Design exhaust temperature 55.16℃ 55.56℃ 55.16℃ 52.1℃
Low heating value of natural gas 35590KJ/Nm³ 35590KJ/Nm³ 35590KJ/Nm³ 35590KJ/Nm³
Heating surface area Radiation 6.93㎡ 9.73㎡ 14.67㎡ 19.41㎡
convection 13.55㎡ 28.89㎡ 52㎡ 91.13㎡
Energy saving device 11.84㎡ 22.56㎡ 32.16㎡ 56.16㎡
condenser 14.8㎡ 28.2㎡ 48.24㎡ 74.88㎡
Design fuel consumption 79Nm³/h 158Nm³/h 314.43Nm³/h 470.91Nm³/h
Design thermal efficiency 97.45% 97.43% 97.45% 97.58%
Condensation conversion thermal efficiency 100.6% 100.58% 100.6% 100.73%
RIELLO low nitrogen gas burner Burner back pressure 1050Pa 900Pa 1300Pa 1600Pa
output power 300/600~1300KW 300/930~1860KW 500/1500~4450KW 1000/2200~6250KW
flow 30/60~130Nm³/h 30/93~186Nm³/h 50/150~440Nm³/h 100/220~620Nm³/h
Motor power 2.2KW 4.5KW 9.2KW 15KW
Comparison method Mechanical tuning Electronic tuning Electronic tuning Mechanical tuning
NOx emission concentration <80mg/Nm³ <80mg/Nm³ <80mg/Nm³ <80mg/Nm³
Water supply pump electric power 2.2KW 3KW 4KW 5.5KW
flow 1.6m³/h 2.8m³/h 4m³/h 7m³/h
lift 148m 153m 158m 156m
Excess air coefficient at the exit 1.075 1.075 1.075 1.075
Boiler body weight 3260Kg 5450Kg/td> 8766Kg 10220Kg
Weight of energy-saving device body 216Kg 816Kg
Weight of condenser body 290Kg 1108Kg
Boiler transportation weight 6300Kg 8220Kg 11830Kg 15300Kg
Boiler transportation dimensions (length, width, height) 3750*2020*2870mm 4286*2181*3135mm 5186*2470*3590mm 5830*2520*3050mm
Boiler installation dimensions (length, width, height) 4250*3215*3165mm 4855*3425*3400mm 6105*3655*3700mm 6750*4010*3980mm
Power Consumption 4.4KW,
Online inquiry
  • Contacts
  • Company
  • Telephone
  • Email
  • WeChat
  • Verification Code
  • Message Content

Successful operation!

Successful operation!

Successful operation!