VIP member
Laboratory Sample Bottle Washing Machine
Laboratory Sample Bottle Washing Machine
Product details
The laboratory sample bottle washing machine has the function of pumping non pressure deionized water (ultrapure water) into the bottle, the water softener automatically starts, and has the function of detecting salt deficiency alarm. It is equipped with a built-in peristaltic pump to dispense cleaning and neutralizing agents, a preheating function for water inlet, and a circulation pump (maximum flow rate) of 400L/min.
1Laboratory environmental conditions:
The laboratory used for installing instruments should have a good external environment. The laboratory should be located in a nearby area without strong electromagnetic fields or sources of strong thermal radiationIt should not be built near equipment and workshops that generate severe vibrations, and should avoid direct sunlight, smoke, polluted airflow, and water vapor.
The internal environment of the laboratory should be kept clean, and the indoor temperature should be controlled within0-40 ℃, the relative humidity of indoor air should be less than 70%.
2Laboratory equipment conditions:
Instrument host volume760m x 980m x 1100m (length x width x height), leave a distance of no less than 0.5 meters from the wall around the bottle washing machine for your operation and future maintenance.
The laboratory should be equipped with tap water(A tap is also available, just like a fully automatic washing machine), the tap water pressure is not less than 0.1MPA. If two pure water washes are required, a pure water source (not less than 60L water bucket) must be provided, and the instrument is equipped with a booster pump for water inlet. The instrument is equipped with a 4-wire water distribution pipe at the factory.
3Laboratory power distribution requirements:
The laboratory should be equipped with communication facilities220V, with an incoming wire diameter of not less than 4mm2. Require a single-phase air protection switch with a capacity of 32A to be connected. The instrument has an exposed cable of 5 meters,
4. Instrument requirements:
（1) Two water sources are required: tap water requires a 4-point external thread interface, pure water tanks or pipelines require a 4-point external thread, and the inlet pipe length is 2 meters.
（2) Require there to be drainage near the instrument, which should be the same as the drainage pipe of the washing machine. The length of the drainage pipe should be 2 meters, and the height of the drainage outlet should not exceed 0.5 meters.
4. The instrument should be reliably grounded:
The best ground wire is directly buried underground with one pieceLead out a metal copper plate with a depth of less than 1m and connect it to the ground terminal of the power supply incoming line.
5. Specific parameters of bottle washing machine
1. Power supply section
1.1 Voltage:220v50HZ
1.2 Heating power:4Kw
1.3 Washing pump power:700w
1.4 Total power consumption of the instrument:5KW
1.5 Drying power:1kw
2. Program
2.1 Customizable Programming（10 custom programs)
2.2 Ten prefabricated programs
3. Cleaning function
3.1 Circulating pump(Maximum flow rate) 400L/min
3.2 The water softener automatically starts and has the function of detecting salt deficiency alarm
3.3 It has the function of pumping non pressure deionized water (ultrapure water) into the system
3.4 Built in peristaltic pump for dispensing cleaning and neutralizing agents
3.5 Inlet preheating function
4. Control system
4.1 Control System for Optical Isolation Circuit Design
4.2 Electronic safety lock: prevents the instrument from being opened during operation
4.3 Main washing pump over temperature protection, cleaning chamber over temperature protection, to prevent instrument from dry burning, idling, etc
4.4 Overflow Protection: High precision water pressure sensor to prevent water overflow from contaminating the laboratory
4.5 RS232 interfaceExperimental data printing function, providing users with traceable data records
4.6 HEPA filter, compressed air flow rate55m ³/h, to avoid secondary pollution in the cleaning chamber
5. Clean the basket frame
5.1 350th Sample Bottle Cleaning Rack
6. Instrument dimensions
Instrument dimensions: lengthX Width X Height 788X730X1673 (mm)
Online inquiry
-
Contacts
-
Company
-
Telephone
-
Email
-
WeChat
-
Verification Code
-
Message Content
-