Electron microscope active vibration reduction tableAVI-600M, Widely used for large-scale electron microscopy isolation of brands such as Zeiss ZEISS, Leica Leica, Hitachi HITACHI, JEOL, as well as isolation of semiconductor equipment, large jammers, and precision electronic balance equipment. Suitable for various large microscopes such as AEMSEMATMTEM, active vibration reduction tables for profilometers, active vibration reduction tables for electronic Taiping, and active vibration reduction tables for laser equipment!

Product Description:

The AVI-600M active vibration isolation system for electron microscopes and similar large research instruments is a compact modular system that provides industry-leading active vibration isolation performance over a wide frequency range, starting from 0.5 Hz. The AVI series platform helps users gain more benefits from microscopes by eliminating destructive low-frequency vibration noise that affects measurements. The platform adopts a low-key modular design, which eliminates the need for lifting devices for most instruments (including most SEM), simplifying the installation process.

Suitable for various types of large electron microscopes such as AEMSEMATMTEM, interference analyzer shock absorbers, profilometer shock absorbers, electronic Taiping shock absorbers, ultrafast laser system shock absorbers, time-frequency system shock absorbers, large semiconductor equipment shock absorbers, and laser equipment active shock absorbers.

working principle:

Isolation table - Anti vibration table uses electrical control to immediately eliminate vibration by applying a force in the opposite direction to the incoming vibration. Sensors continuously monitor vibrations, and based on this information, actuators generate forces in opposite directions and continue to produce optimal vibration isolation. The active isolation platform is good at isolating vibrations in the low-frequency range below 10Hz.

The AVI series isolation table adopts advanced isolation technology and is suitable for any research situation. It can isolate vibrations in 6 degrees of freedom, including horizontal and vertical directions. The AVI series platform utilizes the piezoelectric acceleration sensor inside the controller to sense the incoming vibration from the outside. By converting the pressure information from the outside into an electrical signal and sending it to the piezoelectric transducer in the isolation module, the transducer generates a pressure signal that is equal in magnitude and opposite in phase to the incoming pressure to eliminate the incoming vibration. The isolation system utilizes a feedback loop to eliminate mechanical resonance in the isolation system. It can isolate vibration from the ground and provide a stable testing environment for precision instruments such as electron microscopes and optical devices that are sensitive to vibration in the laboratory.

Technical parameters of electron microscope active vibration reduction table:

• model: AVI-600M/LP
• System configuration: Independent isolation device&control device
• Active isolation range: approximately 1.0 Hz to 200 Hz
• Passive isolation range: approximately above 200 Hz
• Display screen signal: The multiplexed signal is used for the vibration level of oscilloscope displays with and without isolation.
• LEDs indicate the overload situation during the output phase.
• Unit size (each): 288 x 720 x 112.5 Hmm
• Controller size: 448 x 286 x 143 Hmm
• Weight of isolation unit: 26kg
• Load capacity: 1200 kg (equivalent/low center of gravity)
• Input voltage: 90 – 125 VAC / 200 – 250 VAC, 50 – 60 Hz
• Power consumption: typically 27W
• Correction force: maximum horizontal 12N, maximum vertical 24N
• System noise: 0.1-200Hz, below 50nG/√ Hz in any direction
• Static flexibility: about 1 µ m/N vertically, about 2 µ m/N horizontally
• Temperature range: 5 ℃ -40 ℃
• Relative humidity: 10-90% (5-30 ℃), 10-60% (30-40 ℃)
• Indoor/Outdoor Use: Only for indoor use

Upgrade options:

• The AVI-600M electron microscope active vibration isolation platform can be used in conjunction with the LFS low-frequency stabilizer to enhance the low-frequency isolation effect, with the isolation frequency extending to 0.5Hz in the low-frequency range.

Electron microscope active vibration reduction tableVibration isolation effect:

Performance comparison chart: SEM researchers conducted imaging under two unique conditions: without isolation system and with AVI series isolation stage. When using AVI series vibration isolation table with SEM, the obtained images show a significant improvement in image quality and overall measurement clarity.

Electron microscope shock absorption, demagnetization and sound insulation integrated solution, as well as active demagnetization system and soundproof box